Featured image for article: Drop and Hook vs Live Load Hours Pay and What to Check

Short answer

On a live load you wait at the dock while the trailer is loaded or unloaded. On a drop and hook you leave one trailer and take another that is already loaded or empty, so the stop can be short. For an owner-operator the difference shows up in two places. Hours: time waiting and loading at a shipper counts as on-duty time under federal hours of service rules, and it runs down your 14-hour window. Pay: a live load is paid back through detention only if the rate confirmation says so and you claim it, while a drop and hook can carry its own costs, such as a trailer you did not see loaded.

This guide is for dry van and reefer owner-operators deciding which loads to take. It covers how each stop type spends your hours, where the money goes on each one, and what to check before you hook a trailer you did not watch being loaded.

What the terms mean on a rate confirmation

TermWhat happens at the dock
Live loadYou back into a door and wait while the shipper loads your trailer, then you get the paperwork and leave.
Live unloadThe same at the receiver: you wait while the trailer is unloaded.
Drop and hookYou drop the trailer you brought and hook a different one, loaded or empty, from the yard.
Preloaded trailerThe shipper loaded a trailer before you arrived. You hook it and go, often after bringing an empty in exchange.
MixedOne end is a drop, the other is live. A preloaded pickup with a live unload is common, so read both stops.

The stop type belongs in the rate confirmation for both the pickup and the delivery. If it is missing, ask before you book. Our load acceptance checklist puts it on the list of things to confirm before you say yes.

How each stop type spends your hours

Federal hours of service rules do not treat waiting at a dock as free time. Under 49 CFR 395.2, on-duty time includes time at a shipper’s property “waiting to be dispatched, unless the driver has been relieved from duty by the motor carrier,” and all time “loading or unloading a commercial motor vehicle, supervising, or assisting in the loading or unloading, attending a commercial motor vehicle being loaded or unloaded.”

That on-duty time sits inside the limits in 49 CFR 395.3:

  • The 14-hour window. You may not drive after 14 consecutive hours from coming on duty following 10 consecutive hours off. Hours spent at a dock count against those 14.
  • 11 hours of driving. Driving is capped at 11 hours inside that window. A long live load does not use driving time, but it shrinks the window you have left to drive in.
  • The 30-minute break. After 8 hours of driving you need a 30-minute interruption, and the rule says it can be satisfied by off-duty, sleeper berth or on-duty not driving time. A wait at the dock can count toward the break, but it does not stop the 14-hour clock.

In practice: on a day with a long live load at the pickup and a live unload at the end, the dock time can use up enough of the window that the run no longer fits in one day, even though the miles would. On a drop and hook at both ends, the stops take less of the window and more of it is left for driving.

A day on each, with made-up numbers

Every number below is hypothetical, picked to show the arithmetic. It is not a typical wait time.

ItemLive at both ends (hypothetical)Drop and hook at both ends (hypothetical)
Pre-trip and paperwork0.5 h0.5 h
Pickup stop3 h0.75 h
Delivery stop3 h0.75 h
Non-driving hours used6.5 h2 h
Left of the 14-hour window for driving7.5 h12 h, capped at 11 by the driving limit

In this example the live day leaves 7.5 hours to drive and the drop and hook day leaves the full 11. If the run needs 9 hours of driving, the live version does not finish that day, and the next load starts a day later. That lost day is the real cost of a long live load, and it is why a lower rate on a drop and hook can earn more per week than a higher one on a live load.

Where the money goes on a live load

  • Detention. Waiting past the free time is paid only if the rate confirmation includes detention and you document arrival and departure times. Our guide to detention pay covers what to record and how to claim it.
  • Lumpers. Some receivers require a third party to unload, and someone has to pay for it. Who pays, and how to get reimbursed, is in our guide to lumper fees.
  • Fuel and reefer run time. A reefer unit keeps running while you wait at the door, and an idling truck burns fuel. Neither is paid back unless the rate confirmation says so.
  • The next load. If the wait pushes you past the window, you may lose the reload you lined up for the next morning.

Where the money goes on a drop and hook

Drop and hook saves time when the trailer pool works. When it does not, the cost shifts to you in other ways:

  • Hunting for the trailer. A trailer that is not where the paperwork says, or is not ready, turns a quick stop into a wait anyway.
  • Empty miles to get a trailer. If you need an empty to swap and do not have one, you may have to pull one from another yard first.
  • Weight you did not watch. A preloaded trailer can be over on an axle, and the ticket is yours to deal with (more below).
  • The trailer’s condition. Tires, lights and brakes on a trailer you hook become your responsibility once you drive it.

If you run power only, where every load is a trailer someone else owns, the trailer pool decides most of your week. We cover that math in power-only dispatch: the loaded-mile math.

Before you hook a trailer you did not see loaded

  1. Inspect it. Under 49 CFR 396.13, before driving you must “be satisfied that the motor vehicle is in safe operating condition.” A trailer from a yard gets the same check as your own.
  2. Match the seal and the paperwork. Check that the seal number on the door matches the bill of lading and the trailer number matches what you were sent for. Write any difference on the paperwork before you leave.
  3. Note that you did not watch the load. If the bill of lading allows it, make sure it shows the trailer was loaded and counted by the shipper, so a shortage at delivery is not put on you by default.
  4. Scale it. On the Interstate System, 23 CFR 658.17 sets 80,000 pounds gross, 20,000 on a single axle and 34,000 on a tandem, with the bridge formula on top. A preloaded trailer with the weight in the wrong place can be legal on gross and still over on an axle. Scale it close to the pickup, where you can still go back.
  5. Reefer: check the set point. Compare the unit’s setting with the temperature on the paperwork, and record the reading before you leave the yard.

Which loads to look for

Neither stop type is always better. Compare the two on what the week pays, not on the rate alone.

  • A live load can be worth it when the rate covers the hours it uses, detention is in the rate confirmation, and the shipper is known for loading on time.
  • A drop and hook can be worth it when it keeps you inside the window for the next pickup, even at a lower rate.
  • Reefer runs more live loads. Many reefer loads are loaded and unloaded live at the dock, so detention terms and reefer fuel matter more there. More on reefer dispatch is on our reefer page.

Frequently asked questions

What does drop and hook mean in trucking?

You drop the trailer you brought at the shipper or receiver and hook a different trailer, loaded or empty, instead of waiting while your own trailer is loaded or unloaded.

Does waiting at the dock count against my hours?

Yes, unless the motor carrier has relieved you from duty. Under 49 CFR 395.2, waiting at a shipper’s property and loading or unloading are on-duty time, and on-duty time counts toward the 14-hour window.

Can I take my 30-minute break while I am being loaded?

Under 49 CFR 395.3, the 30-minute interruption can be satisfied by on-duty not driving time, so time at the dock can count as the break. It still counts toward the 14-hour window.

Do drop and hook loads pay less?

The rate can be lower per load, but compare by the week. A drop and hook that saves hours can let you take another load sooner, while a live load only pays back for waiting if detention is in the rate confirmation.

Who is responsible if a preloaded trailer is overweight?

You are driving it, so the ticket at the scale is yours to deal with. Scale it near the pickup and ask the shipper to rework it if an axle is over.